Menu

Discussion Forum

New Discussion
Filtern

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

about transmission/reflection coefficients of a nano grating

Posted 11.04.2012, 11:16 GMT-4 RF & Microwave Engineering Version 4.2a 6 Replies

Hongtao Zhang
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,

This question is related to my old message (www.comsol.com/community/forums/general/thread/27434/)
It is about a calculation of transmission/reflection coefficients of a nano grating. I list the problem description and code at the attachment.

After modifying some parameters, I can plot the curve of Transmission/Reflection coefficients in COMSOL. However, there exist several unnecessary oscillations in the curve, which also depends on the grid size. This calculation is not correct and contracts with our known analytic results.

In addition, this mode is related to anomaly effect of grating. I notice from this forum that there may be some problem in calcuation by COMSOL. I am confusing by where the problem comes from. Any suggestion is welcome.

Thanks.

Hongtao
6 Replies Last Post 12.04.2012, 07:08 GMT-4
Alexander Kuznetsov
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 11.04.2012, 13:05 GMT-4
your top and bottom domains are way too large. With you default mesh you don't have enough mesh elements per wavelength. Maximum element size 150 nm with lambda 600 nm is not enough, especially for oblique angles.
your top and bottom domains are way too large. With you default mesh you don't have enough mesh elements per wavelength. Maximum element size 150 nm with lambda 600 nm is not enough, especially for oblique angles.
Hongtao Zhang
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 11.04.2012, 15:41 GMT-4
Thanks you, Alexander!

I will modify this distance and re-do the calculation. WIll discuss with you later.


Hongtao


your top and bottom domains are way too large. With you default mesh you don't have enough mesh elements per wavelength. Maximum element size 150 nm with lambda 600 nm is not enough, especially for oblique angles.




Thanks you, Alexander! I will modify this distance and re-do the calculation. WIll discuss with you later. Hongtao [QUOTE] your top and bottom domains are way too large. With you default mesh you don't have enough mesh elements per wavelength. Maximum element size 150 nm with lambda 600 nm is not enough, especially for oblique angles. [/QUOTE]
Qiao Ma
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 11.04.2012, 17:42 GMT-4
I was always stuck with the same problems, there exists some resonance peak in small wavelength range (www.comsol.com/community/forums/general/thread/27642/#p75220).

Regards!
I was always stuck with the same problems, there exists some resonance peak in small wavelength range (http://www.comsol.com/community/forums/general/thread/27642/#p75220). Regards!
Hongtao Zhang
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 11.04.2012, 19:15 GMT-4
yeah, that is what I am figuring out. The resonance peak should only be one for the thin film.

I did not know why I have so many peaks.

By the way, Qian, could you send me your code if feasiable by my email address: hzhang2012@gmail.com.
We can discuss this problem.

Hongtao
yeah, that is what I am figuring out. The resonance peak should only be one for the thin film. I did not know why I have so many peaks. By the way, Qian, could you send me your code if feasiable by my email address: hzhang2012@gmail.com. We can discuss this problem. Hongtao
Qiao Ma
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 12.04.2012, 03:30 GMT-4
Sure, I will send my code to you.

Sure, I will send my code to you.
Qiao Ma
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 12.04.2012, 07:08 GMT-4
I have sent the code to you!
Please check your email!
Looking forward to discussing with you!

Regards!
I have sent the code to you! Please check your email! Looking forward to discussing with you! Regards!

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content