Menu

Discussion Forum

New Discussion
Filtern

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Geometry visualization

Posted 29.03.2010, 00:33 GMT-4 5 Replies

Omar Canales
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,

I am drawing a very thin block (cross section: 200 microns X 50 microns) which is very long (10 mm in lenght). When I draw such a structure in 3-D and go to the Default 3-D View, I apparently get a "real" view of the structure which is very difficult to visualize. I am wondering if there is a way to get a better representation of it, I mean a "visually shorter structure". After I drew it with the real units, I scaled it in the y-direction (entered Scale Factor = 0.5) but I think I'm just numerically shortening the structure as I can read it from the coordinates. Any of you have a suggestion for this?

Thanks in advance!

-Omar
5 Replies Last Post 30.03.2010, 02:12 GMT-4
Jim Freels mechanical side of nuclear engineering, multiphysics analysis, COMSOL specialist
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29.03.2010, 13:51 GMT-4
Yes. Under "options", pick axis settings. Unclick "equal length" (or something like that, from memory). Then click "full extents" in the main menu. This will fill the screen optimally for viewing all of your geometry. You can do the same on the post processing.
Yes. Under "options", pick axis settings. Unclick "equal length" (or something like that, from memory). Then click "full extents" in the main menu. This will fill the screen optimally for viewing all of your geometry. You can do the same on the post processing.
Omar Canales
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29.03.2010, 14:41 GMT-4
James, thanks for your response. I tried doing so but I ended up with a deformed geometry...

James, thanks for your response. I tried doing so but I ended up with a deformed geometry...
Jim Freels mechanical side of nuclear engineering, multiphysics analysis, COMSOL specialist
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29.03.2010, 15:37 GMT-4
Yes, it certainly will be deformed.
Yes, it certainly will be deformed.
Omar Canales
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29.03.2010, 16:46 GMT-4
I suspected it, but I'm coming from a very thin long plate to a perfect cube when I unclick "axis equal"...is this what is suppose to happen? Thanks again!
I suspected it, but I'm coming from a very thin long plate to a perfect cube when I unclick "axis equal"...is this what is suppose to happen? Thanks again!
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 30.03.2010, 02:12 GMT-4
Hi

Yes indeed, the deformation is such as the the scaling is free for all 3 directions and it tries to fill in the total screen volume, it very good for MEMS and thin film analysis.

if you want to check the sizes you have the "ruler", or "solve - get initial values (to fill the matrices) + postprocessing point integration X,Y Z coordinates, or edge postprocessing length calculation by integrating "1"

Good luck
Ivar
Hi Yes indeed, the deformation is such as the the scaling is free for all 3 directions and it tries to fill in the total screen volume, it very good for MEMS and thin film analysis. if you want to check the sizes you have the "ruler", or "solve - get initial values (to fill the matrices) + postprocessing point integration X,Y Z coordinates, or edge postprocessing length calculation by integrating "1" Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content