Menu

Discussion Forum

New Discussion
Filtern

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Thermal stress analysis

Posted 14.03.2013, 11:34 GMT-4 Heat Transfer & Phase Change, Materials, Structural Mechanics Version 4.2a, Version 4.3, Version 4.3a 6 Replies

uday
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi sir,

i have analysed thermal stress by passing the laser beam on rectangular plate (through structural mechanics module).i used stainless steel temp dependent material properties to my simulation. i used elasto plastic properties yield and tangent modulus. i have attached the properties also.i satisfied with results of deformation of plate and temperature profile. but my major problem is von mises stress exceed the ultimate stress level.

how can i reduce the stress value??

is there any possible to use smooth function.

please help me genius.
6 Replies Last Post 15.03.2013, 10:18 GMT-4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 14.03.2013, 18:13 GMT-4
Hi

I do not catch you there ? smoothing the table values (use an interolation functon with a higher order setting) will not change the stress reached, or ?

--
Good luck
Ivar
Hi I do not catch you there ? smoothing the table values (use an interolation functon with a higher order setting) will not change the stress reached, or ? -- Good luck Ivar
uday
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15.03.2013, 04:35 GMT-4
dear ivar,

Thanks for your reply.i used temperature dependent properties by using interpolation function.but i am getting 700mpa von mises stress .but stainless steel ultimate tensile strength is 515 mpa.

i used interpolation function.but what is higher order setting??

can you help me?
dear ivar, Thanks for your reply.i used temperature dependent properties by using interpolation function.but i am getting 700mpa von mises stress .but stainless steel ultimate tensile strength is 515 mpa. i used interpolation function.but what is higher order setting?? can you help me?
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15.03.2013, 07:11 GMT-4
Hi

first of all I hope its Mega and not milli Pascal you are referring to ;)
But I do not catch you, is it the interpolation function that get far out, or is it the results of your simulation ?

--
Good luck
Ivar
Hi first of all I hope its Mega and not milli Pascal you are referring to ;) But I do not catch you, is it the interpolation function that get far out, or is it the results of your simulation ? -- Good luck Ivar
uday
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15.03.2013, 09:20 GMT-4
Dear ivar,
sorry for my explanation. this is my final result Von mises stress value about 700 Mega Pascal. von Mises stress I got from Comsol too high (>>yield strength of materials) than I expected.
Dear ivar, sorry for my explanation. this is my final result Von mises stress value about 700 Mega Pascal. von Mises stress I got from Comsol too high (>>yield strength of materials) than I expected.
Nagi Elabbasi Facebook Reality Labs
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15.03.2013, 10:18 GMT-4
The ultimate tensile strength of the material is not accounted for in the elastic-plastic material model you are using. Therefore if the strains are high enough you can get stresses around 700 MPa. That would require a very large temperature increase though and an overly constrained structure. What temperature increase are you applying? Check also that you are using an elastic-plastic material and not just elastic.

Nagi Elabbasi
Veryst Engineering
The ultimate tensile strength of the material is not accounted for in the elastic-plastic material model you are using. Therefore if the strains are high enough you can get stresses around 700 MPa. That would require a very large temperature increase though and an overly constrained structure. What temperature increase are you applying? Check also that you are using an elastic-plastic material and not just elastic. Nagi Elabbasi Veryst Engineering
Nagi Elabbasi Facebook Reality Labs
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 15.03.2013, 10:18 GMT-4

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content