Menu

Discussion Forum

New Discussion
Filtern

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Material property across the interface

Posted 13.04.2016, 08:10 GMT-4 Geometry Version 5.2 6 Replies

Shujun Xian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,

I assign two materials with different conductivity values (sigma1 and sigma2) into two adjacent objects. In the geometry list - Form Assembly(fin), we can chose form an assembly or form a union. Is there any difference in these two methods regarding the sigma value when pass across the interface between object1 and object2? To be more specific, will the sigma1 sharply drop to sigma2 when forming an assembly, while sigma1 decreases to sigma2 in a continuous way when forming a union?


Thanks for your reply very much!

Kind regards,
Shujun
6 Replies Last Post 15.04.2016, 03:44 GMT-4
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 14.04.2016, 09:29 GMT-4
Hello Shujun,
You may find this link helpful:
www.comsol.com/support/knowledgebase/1216/
Best regards,
Jeff
Hello Shujun, You may find this link helpful: https://www.comsol.com/support/knowledgebase/1216/ Best regards, Jeff
Shujun Xian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 14.04.2016, 10:24 GMT-4
Hi Jeff,

Thanks for your reply!

In the document, it says that by default, continuity of the fields and the fluxes will be maintained across the interior boundaries in Form Union but not in Form Assembly. So, I suppose one can say that the conductivity changes in a more continuous way in forming union than in forming assembly when across the interior boundaries?

Regards.
Hi Jeff, Thanks for your reply! In the document, it says that by default, continuity of the fields and the fluxes will be maintained across the interior boundaries in Form Union but not in Form Assembly. So, I suppose one can say that the conductivity changes in a more continuous way in forming union than in forming assembly when across the interior boundaries? Regards.
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 14.04.2016, 11:25 GMT-4
No, one cannot infer that. The conductivity in each domain will be what you set it to in either case.
Jeff
No, one cannot infer that. The conductivity in each domain will be what you set it to in either case. Jeff
Shujun Xian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 14.04.2016, 13:50 GMT-4
Ok. So, in this case, the conductivity will drop sharply to sigma2 when crossing the interior boundaries, no matter we form union or form assembly?
Ok. So, in this case, the conductivity will drop sharply to sigma2 when crossing the interior boundaries, no matter we form union or form assembly?
Jeff Hiller COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 14.04.2016, 15:22 GMT-4
That's right.
Jeff
That's right. Jeff
Shujun Xian
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 9 years ago 15.04.2016, 03:44 GMT-4
I get it. Thank you Jeff.

Shujun
I get it. Thank you Jeff. Shujun

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content